Your Shopping Cart Is Empty!
If you already have an account, Sign in.
If you already have an account, Sign in.
Categories
Features:
1>. The product is easy to install and can be used in the hole welding line.
2>. There are fixed mounting holes in the corners to prevent the movement/vibration of the product without power, and the fixed hole is 3.2mm.
3>. Universal input voltage: 85-264V AC or 110-370V DC.
4>. High efficiency, low output ripple noise, double isolation output, high output voltage of main road (VO1).
5>. Input and output high isolation.
6>. With over-current protection, short circuit protection and temperature protection.
7>. The output is built in double - channel LC -π type filtering without external circuit.
Input Characteristic:
| No. | Input | Value |
| 1 | AC input(VAC) | 85-264 |
| 2 | DC input(VDC) | 110-370 |
| 3 | Frequency range(Hz) | 47-63 |
| 4 | Input current(A) | 1/115VAC 0.5/230VAC |
| 5 | Surge current(A) | Cold start:20A/230VAC |
| 6 | Workpiece ratio(TYP.) | 69 |
| 7 | Stand-by consumption(mA) | ≤1W/230VAC |
Output Characteristic:
| Input voltage(VDC) | ± 5V | |
| Input voltage precision | Main circuit: ±1%, Side circuit: ±10% | |
| Rated current(ADC) | 1.7A | |
| Rated power (W) | 17W | |
| Ripple and noise(mvp-p> | Rated input voltage, 20MHz band width | V01(V+)Mian circuit: 50mV |
| V02(V-) Side circiut: 100mV | ||
| Line Regulation | Full load | ±1% |
| Load Regulation | 10-100% load | ±3% |
| Start/up time | Full load |
2000ms, 30ms/l 15VAC 1000ms, 30ms/230VAC |
| Maintain (ms) | Full load |
16ms/l 15 VAC 50ms/230VAC |
| Overload protection | Rated input voltage | 115%^150% of rated output power |
| Protection mode: hiccup mode, the abnormal condition of abnormal load can be automatically returned. | ||
| Short-circuit protection | Rated input voltage | Long - term short circuit, self - recovery |
| Over-current protection | >1.1 time Io | |
| Start delay time(ms) | Vin:230 VAC | 500ms |
| Power-off protection time(ms) | 20ms | |
General Characteristic:
| Working temperature(℃) | / | -30 to 70 |
| Working humidity(RH) | / | 20 to 90%, non-condensing |
| Temperature drift coefficient | / | ±0.02%/℃ |
| Storage temperature and humidity | -40 to 85 Celsius 10-95%RH | |
| Switching frequency(KHz) | 20-65 | |
| Insulation voltage（VAC） |
Input to output Test 60s, ≤5 mA |
3000 |
| Insulation resistance (M Ohm) | Input to output500VDC | 100 |
| leakage current（mA) | 500VDC | Input to output ≤ImA/RMS Value |
| MTBF | @25 Celsius | 215000h |
| Safety class | / | Suitable for： CLASS B |
| Beam vibration | / | 10—500Hz 2G 10Minutes/cycle. X, Y, Z 60minutesrespectively |
| electromagnetic compatibility | / | Suitable for：EN55022(C1SPR22）Class B EN61000-3-2,-3 |
| Remark | 1. Except for special instructions, the parameters of this specification are measured at 230VAC, rated load and 25c ambient temperature. | |
| 2. Ripple and noise measurement method: use a 12 "twisted pair, and the terminal shall be connected in parallel with the capacitance of 0.1uf and 10uF, and shall be measured at 20MHz bandwidth. | ||
| 3. Accuracy: including the rounding error, linear adjustment rate and load adjustment rate. | ||
| 4. The power supply shall be regarded as part of the internal components of the system, which shall be confirmed by electromagnetic compatibility with the terminal equipment. | ||
| 5. The output should be reduced under low input voltage. | ||
Wiring Instruction:
1>. Typical circuit:
Output:
| Output voltage | C1/C3 | C2/C4 | TVS |
| 5V |
C1: 47uF/25V C3: 100uF/35V |
IUF/50V | SMBJ7.0A |
| 7V | SMBJI2.0A | ||
| 12V | SMBJ20.0A | ||
| 24V | SMBJ30A |
Remark:
C1: connection/coupling filter electrolytic capacitors.High frequency low resistance capacitance is recommended. The noise from the connector can be removed when the capacitance pressure drop is greater than 75%.
C2: ceramic capacitors to remove high frequency noise.
TVS: protection of the back - level circuit when the power supply is abnormal. Recommended.
C1, C2, C3, C4: the product with no requirement for power output ripple is not used.
2>. Emergency solution--Recommended circuit:
Input:
| Component No./ Recommended component | Function | Recommended value |
| CX1 capacitance | Restrain the interference of common mode, improve the anti-jamming ability and reliability of the system. | 0.22uF/275VAC |
| R1/R2: leakage resistance. | 1M ohm 1/2W | |
| NF: common mode inductance. | 10 mH-30 mH |
Pin Definition:
ICStation doesn't accept any form of pay on delivery. Items used to be shipped after payment. Below are the payment methods we can accept at the moment:
1) Paypal Payment
PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at icstation.com to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account).
We are PayPal Verified 
2) Bank Transfer / Wire Transfer / T/T
.jpg){kind=spacer}
Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$300. The bank will charge about US$50 for the transfer fee if we do the payment in these ways. Feel free to contact us for bank payment details if you need pay via bank.
For other payment method, please contact us at orders@icstation-team.com for more details.
