2.4G 6-Channel Remote Control Wireless Transceiver DIY Kit for Robotics and Motors

prev
next

TX/RX-2.4G 6-Channel Remote Control Wireless Transceiver DIY Kit for Robotics and Motors

$6.99

~~$9.99~~30%

Quantity	3+	5+	10+
Price	$6.90	$6.80	$6.60

00d : 00h : 00m : 00s

Item ID: 13280

Add to Cart

Share Facebook Google Pinterest VKontakte Reddit

Product Details

Description:
This is a DIY Kit Wireless Transceiver Module for Robot/Motor. You need solder it by yourself. It sends signals via wireless communication. It can be used at Robotics, smart home, research and education, model aircraft and so on.

Features:
1>. High sensitivity;
2>. Low power;
3>. Long distance communication;
4>. Low power consumption;
5>. DIY design;

Parameters:

No.	Parameter	Value
1	Transmitter Model	TX-2.4G
2	Standby Current	Less than 25uA
3	Soldering Difficulty Level	Easy
4	Working Voltage	DC 2V-3V
5	Working Current	0.8A
6	Transmitter Distance	100m(max)
7	Communication Frequency	2.4GHz
8	Transmitting Antenna	Built in
9	Shell Size	1006025mm
10	Receiver Model	RX-2.4G
11	Standby Current	Less than 6mA
12	Soldering Difficulty Level	Easy
13	Working Voltage	DC 3V-12V
14	Working Current	1.6A(max)
15	Communication Frequency	2.4GHz
16	Transmitting Antenna	Built in
17	PCB Size	49.5*35.5mm

Instructions:
Step 1: Complete the installation in the normal way following installation manual and schematic.(Please request separately).
Step 2:Connect DC motor;
Step 3:Connect power supply for transmitter and receiver.
Step 4:Test and use.

Key Instructions:
1>.S1 and S2 are used to control Motor M1 to Clockwise rotation and counterclockwise rotation.
2>.S3 and S4 are used to control Motor M2 to Clockwise rotation and counterclockwise rotation.
3>.S5 and S6 are used to control Motor M3 to Clockwise rotation and counterclockwise rotation.

Using Attention:
1>.Please make sure all components in right direction and right place.
2>.Please check whether pseudo/float welding.This is very important .
3>.The soldering iron can't touch the components for a long time, otherwise the components will be damaged because of the high temperature.
4>.It is recommended to use a stable power supply, otherwise it may interfere with the signal output.

Component List:

NO.	Component Name	PCB Marker	Parameter	Quantity
TX-2.4G
1	Metal Film Resistor	R1	1K	1
2	Ceramic Capacitor	C3	0.1uF 104	1
3	Electrolytic Capacitor	C1,C2	10uF	2
4	LED Spacer	LED1	3mm	1
5	Red LED	LED1	3mm	1
6	Button	S1-S4	669mm	4
7	Button	S5-S6	668mm	2
8	Switch	S8	1268mm	1
9	Oscillator	X1	12MHz	1
10	3P Male Pin	J1	2.54mm	1
11	TXS2.4G	U1	SOP-16	1
12	Jumper Cap	J1	2P 2.54mm	1
13	PCB	TX-2.4G	9.6*5.5cm	1
14	Plastic Box		1062.5cm	1
15	Key Cap	S1-S6	White	6
16	Screw		PA2.6*5	4
17	Screw	Bat Box	M2*5	2
18	Nut	Bat Box	M2*5	2
19	Battery Box		AA*2	1
RX-2.4G
20	Ceramic Capacitor	C2-C3	0.001uf 102	2
21	Electrolytic Capacitor	C4	1uF	1
22	Electrolytic Capacitor	C1	100uF	1
23	L9110	U2-U4	DIP-8	3
24	HT7133	U5	TO-92	1
25	RXS2.4G	U1	SOP-16	1
26	Oscillator	X1	12MHz	1
27	Switch	S1	SS12D07	1
28	2P Socket	CN1-CN4	2.54mm	4
29	2P Connector Cable	CN1-CN4	15cm	4
30	PCB	RX-2.4G	49.5*35.5mm	1

Note: You can finish installation by PCB silk screen and component listing.

Application:
1>.Robotics
2>.Smart home
3>.Research and education
4>.Model aircraft

Frequency asked questions:
1>.Why can't work?
Q :Please make sure all components in right direction and right place and check whether pseudo/float welding.This is very important.

Install tools you need preliminary preparation by yourself:
1>. Soldering iron;
2>. Multimeter;
3>. Solder wire;
4>. Iron stand;
5>. Diagonal cutting pliers;
6>. The screwdriver;
7>. Tweezers;
8>. Long nose pliers;
9>. Suction tin;
10>. Cleaning sponge;
11>. Screwdriver set.