RJ45M20Y2 Ethernet Electric Cable Plug Socket Wire Connector, RJ45 Connector, Female to Female for CAT 6/CAT 5

Instruction:

RJ45 waterproof Ethernet LAN cable coupler compatible with CAT 5, CAT 5E, CAT 6 patch cord.

Female to female panel mount, plug and play. The threaded connecting design makes it solderless and no need to damage or interrupt the original wire, so there is no signal degradation.

IP65 class waterproof and dustproof protection make it suitable to be used in harsh industrial or outdoor environments. It is very much ideal for printers, PCs, routers, computer servers, switch boxes, network media players, POE devices...This is a good solution to protecting Ethernet connections that are exposed to the weather.

IMPORTANT: Since the female sockets at both ends have different depths, please cut off the excess part and make the top end of the clip protrudes no more than 5mm.

ATTENTION: Failing to properly seat the rubber seal of the coupler and cut off the excess jack clip will result in a leaky connection. Water will enter not only the connector but also your Ethernet cable. If it is used in corrosive soil and moisture, the shell will be more susceptible to corrosion. Please note that IP65 is not resistant to immersion, so DO NOT IMMERSE the connector in water.

RJ45 waterproof Ethernet LAN cable coupler

Female to female panel mount, plug and play. The threaded connecting design makes it solderless and no need to damage or interrupt the original wire, so there is no signal degradation.

IP65 class waterproof and dustproof protection make it suitable to be used in harsh industrial or outdoor environments. It is very much ideal for printers, PCs, routers, computer servers, switch boxes, network media players, POE devices...This is a good solution to protecting Ethernet connections that are exposed to the weather.

Parameters

• Compatible With: CAT 5, CAT 5E, CAT 6
• Material: PVC
• Waterproof: IP65
• Temperature:-40~125°C

• Size: 85mm*25.2mm(O.D.) M20

Female to female

Female to female panel mount, plug and play. The threaded connecting design makes it solderless and no need to damage or interrupt the original wire, so there is no signal degradation.

Instruction

In order to ensure coupling to be waterproof there are a couple of items that you need to complete when you assemble the connector to your cabling. (Thanks to Joe for his contribution)

1. Slide the Elastic Regulator and Waterproof Connector over the end of your Ethernet cable.
2. Plug the Ethernet cable into the Ethernet Female-Female Cable Socket.
3. Cut off the excess part of the jack clip and make the top end of the clip protrudes no more than 5mm.
4. Place the split rubber seal over the Ethernet cable.
5. Screw on the Waterproof connector onto the Ethernet Female-Female Cable Socket. Make sure you fully tighten the Waterproof Connector to properly seat the internal O-ring to create a waterproof connection for that part of the assembly.
6. Screw on the Elastic Regulator which will crimp the split rubber seal creating a waterproof connection around the Ethernet cabling.
7. Repeat the steps above the other side of the connector and you have created a waterproof coupling.

If you are using the Waterproof coupling to attach to an electrical panel there is a nut threaded onto the Ethernet Female-Female Cable Socket and an included rubber washer. Remove the nut from the Female-Female Cable Socket and slide the assembly into the suitably sized hole of your panel or junction box. Keep the rubber washer on the outside of the hold. Screw the nut over the Female-Female Cable Socket from inside they junction box or panel. Tighten the nut sufficiently to make the rubber washer create a waterproof seal.

ATTENTION: Failing to properly seat the rubber seal of the coupler and cut off the excess jack clip will result in a leaky connection. Water will enter not only the connector but also your Ethernet cable.

If it is used in corrosive soil and moisture, the shell will be more susceptible to corrosion.

Please note that IP65 is not resistant to immersion, so DO NOT IMMERSE the connector in water.

Please let us know if you have any question.

ICStation doesn't accept any form of pay on delivery. Items used to be shipped after payment. Below are the payment methods we can accept at the moment:

1) Paypal Payment

PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at icstation.com to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account). 

We are PayPal Verified 

2)  Bank Transfer / Wire Transfer / T/T

Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$300. The bank will charge about US$50 for the transfer fee if we do the payment in these ways. Feel free to contact us for bank payment details if you need pay via bank.

For other payment method, please contact us at orders@icstation-team.com for more details.