DC-DC Step-Down Power Supply Module 75W 5A CVCC Voltage Converter Stabilizer for Battery Charge 4V-38V to 1.25V-36V

1.Description:
  It is a 5A step-down module.There are two modes of constant voltage and constant current. It can be used as a step-down module,battery charger or high-power LED constant current drive module.

2.Feature:
  1).Its conversion efficiency is high.
  2).It supports short circuit protection.
  3).It supports over-temperature protection.
  4).It has a current limiting protection function,even if the output is short-circuited,the module will not be burned out.
  5).It has two modes of constant voltage and constant current.
  6).It has a charging indicator to show the working status.

3.Parameter:
  1).Product Name:5A Step-down Module
  2).Input Voltage:DC 4V~38V
  3).Output Voltage:DC 1.25V~36V
  4).Output Current:5A(Max)
  5).Output Power:75W(Max)
  6).Working Frequency:180KHz
  7).Conversion Efficiency:96%
  8).Work Temperature:-40℃~85℃
  9).Work Humidity:5%~95%RH
  10).Size:61.3*26*12mm

4.Application:

1).Used as an ordinary step-down module with over-current protection capability:
    1.1).Adjust the constant voltage potentiometer to make the output voltage reach the voltage value you want.

    1.2).Use a multimeter to measure the output short-circuit current with a 10A current file (directly connect the two test leads to the output terminal),and adjust the constant current potentiometer to make the output current reach the predetermined overcurrent protection value.(For example,the current value displayed by the multimeter is 4A,then the maximum current when you use the module can only reach 4A,when the current reaches 4A,the red constant voltage constant current indicator will be on,otherwise the indicator will be off)

    1.3).When used in this state,since the output terminal has a current sampling resistor of 0.05 ohm,there will be a voltage drop of 0~0.3V after the load is connected.This is a normal phenomenon! This voltage drop is not pulled down by your load,but dropped to the sampling resistor.

2).Used as a battery charger:
    2.1).The module without the constant current function cannot be used to charge the battery.Because the voltage difference between the exhausted battery and the charger is large,the charging current is too large and the battery is damaged.Therefore,the battery must be constant at the beginning.Current charging,when the charging reaches a certain level,it will automatically switch back to constant voltage charging.

    2.2).Determine the floating voltage and charging current of the rechargeable battery you need;(If the lithium battery parameter is 3.7V/2200mAh,then the floating voltage is 4.2V and the maximum charging current is 1C,which is 2200mA)

    2.3).Under no-load conditions,the multimeter measures the output voltage and adjusts the constant voltage potentiometer to make the output voltage reach the float voltage;(if charging a 3.7V lithium battery,adjust the output voltage to 4.2V)

    2.4).Use a multimeter to measure the output short-circuit current with a 10A current file (directly connect the two test leads to the output terminal),and adjust the constant current potentiometer to make the output current reach the predetermined charging current value;

    2.5).The charging current of the lamp is 0.1 times the charging current;(The current of the battery is gradually reduced during the charging process,and gradually changes from constant current charging to constant voltage charging.If the charging current is set to 1A,then when the charging current is set When it is less than 0.1A,the blue light is off and the green light is on,and the battery is fully charged at this time)

    2.6).Connect the battery and charge it.

    2.7).When operating this method,the input terminal is connected to the power supply,and the output terminal is not connected to the battery without load.

3).Used as a high-power LED constant current drive module:
    3.1).Determine the operating current and maximum operating voltage you need to drive the LED;

    3.2).Under no-load conditions,the multimeter measures the output voltage and adjusts the constant voltage potentiometer to make the output voltage reach the highest LED operating voltage;

    3.3).Use a multimeter to measure the output short-circuit current at 10A current level,and adjust the constant current potentiometer to make the output current reach the predetermined LED operating current;

    3.4).Connect the LED and test the machine.

    3.5).Note that when operating this method,the input is connected to the power supply,and the output is not connected to the LED light when there is no load.

5.LED Indicator:
  1).Red status indicator:
    1.1).Constant current state:Light ON
    1.2).Constant current state:Light OFF

  2).Blue charging indicator
    2.1).Charge:Light ON
    2.2).Full:Light OFF

  3).Green charging indicator:
     Full:Light ON

6.Package:
  1pcs 5A Step-down Module





 

ICStation doesn't accept any form of pay on delivery. Items used to be shipped after payment. Below are the payment methods we can accept at the moment:

1) Paypal Payment

PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at icstation.com to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account). 

We are PayPal Verified 

2)  Bank Transfer / Wire Transfer / T/T

Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$300. The bank will charge about US$50 for the transfer fee if we do the payment in these ways. Feel free to contact us for bank payment details if you need pay via bank.

For other payment method, please contact us at orders@icstation-team.com for more details.